Uncategorized

Hangin’ Drywall For freshies

Hanging Drywall

Have you ever taken the time to watch a competent tradesman hang drywall, you amazing at how fast and easy it seems to be for them. I have seen friends in the trade use activities earthwool johannesburg like a recording measure and a utility chef’s knife to make all the necessary cuts and cut-outs. For the average homeowner who may want to save a few bucks on a home construction project by doing it himself or with a asst, hanging drywall can be very daunting, especially if you have never done it before. There is real physical labor involved here, especially if you are by yourself. I recently redesigned my own bathroom recently which was not bad since it was only 8 feet x 8 feet. Think about a more substantial room such as a new living room in the cellar? I have good news for you. It can be done by yourself or with a asst with a little patience and instruction.

The purpose of this article is to help those who may be just starting out or who are a novice. It will cover the basics of drywalling. The experienced veterans and tradesman have their own way of doing things and have developed their own techniques, cutting corners and trade secrets. If you are just starting out, I recommend buying an extra linen or two of drywall when calculating your job. You will make mistakes and there is no better teacher than experience. If you have a friend who is skilled at drywall, It is advisable to by him a case of his favorite beer and have him come over and give you some pointers as you work.

Lets begin by looking at what tools and supplies you will need to complete your job. Initial thing on the list is the drywall. we need to understand that with drywalling, there is a certain amount of midsection involved. We always want to use the largest pieces possible to create the least amount of seams. The less seams there are to recording and spackle the better off you will be and the smoother your walls will appear. For instance, if i am developing a 10 feet x 10 foott room in my cellar, if at all possible I want to purchase 12 foot drywall boards. Sure you lose two feet to midsection but imagine how many more seams there would be if you used 8 foot boards. Next we start to use a good cord-free drill/driver along with at least 2 or 3 batteries. I also like to have two chargers so i will have one battery charging and one battery at full charge. The preference is an 16 volt cord-free routine. Some people prefer 14. 4 volt for this project. I’ve found that a good 16 volt variable speed cord-free routine can take care of just about any job at home, big or small. You can find whatever you decide and need in regards to a cord-free routine at justcordlessdrills. com. A good method of getting over unity magnetic prop rifle bits are essential also. With 1/2″ sheetrock, I love to use 1 1/2 or 1 5/8 sheetrock screws. I also like to glue my boards to the studs, especially the threshold so a couple of pontoons of adhesive such as Liquid Nails and a caulking rifle is needed. For the beginner, invest in a 4 foot sheetrock sq. This tool will prove invaluable in making your cut-outs for electrical boxes, exhaust fans, etc. Other items you will need are a recording measure, a software application chef’s knife, some carpenter’s pencils, a hand held drywall saw, a corporate which will be long enough to have you the threshold and if you can get one, rent one, or borrow one: a sheetrock lift or jack. This tool is not necessary but will make your job so much easier when doing ceilings. It is especially useful and almost essential if you are alone and have a high threshold. The last thing that you need to make you job easier is a good set of saw horses to lay you drywall boards on when measuring and making cuts.

Lets assume that your room is studded and all the rough electrical, plumbling and duct work is in place. Your room is ready for drywall. When installing drywall, always start with the threshold first. This permits the drywall used for your walls to butt against the perimeter of the threshold drywall to help support it. Make sure that the perimeter of your threshold area has enough stud showing to secure drywall all around. If not, you need to install what are called “nailers” around the threshold perimeter to allow the edges of your threshold drywall to be secured with drywall screws. A nailer is a board that allows you to attach the drywall board edges when a stud or choice is not present. When doing the threshold, we need to go perpendicular to the threshold joists and make sure the ends of the drywall around the threshold perimeter always land on a threshold joist or nailer. Also we need to stagger our threshold joints whenever you can. If you have a 14 foot x 14 foot threshold and are using 12 foot drywall boards, you are going to need one 12 foot board and a 2 foot piece to cover the 14 foot course. A drywall board is 4 foot wide and once you install the next 14 foot course of drywall, install the 2 foot board first and then the 12 foot board so your 2 foot boards are on the opposite end from each other. Be sure the end of a drywall board which will be continued ends in the middle of a joist, stud or nailer.

The first thing that we need to do is take a look at the threshold and see where any cut-outs need to be generated for the lights, exhaust fans, etc. Lets say our first threshold board has two recessed lights. We need to make two measurements: from the wall on a straight line to the center of the light on the length side of the drywall and from the wall on a straight line to the center of the light on the width side of the drywall. Transfer these measurements on to your drywall board by using your linen rock sq and carpenter’s pen. Where the two measurements intersect will be the center of your recessed light. Now measure the diameter of the recessed light. The diameter is length across the light. Partition the diameter by 2 and make use of this rating to draw a circle equal distance from your centerpoint. Use your drywall saw to caught out the circle on the drywall board and once you install the board the cut-out will make with the recessed light. On both length-wise sides of the drywall board, you will see a small bevel. Make sure you butt your next drywall boards bevel to bevel anytime you can.

Now that you have the cut-outs for your drywall board in place, it is time to hang the drywall board. Use your caulking rifle to line all the threshold joists with adhesive where the board will be plalced. If you have a drywall lift, place the board on it and lift it into place. The lift will hold it there so you can start securing it with drywall screws. If you don’t have a lift, I recommend having a asst to do the threshold. A nice little device that you can make is a “T” out of 2×4’s. Make the top the main “T” about 4 feet long, the width of the drywall board. The length should long enough for anyone to stand the “T” upright from the floor to the drywall board at the threshold You can make two or three “T”s” to help support the drywall board while you start buckling it with drywall screws. Secure the board on all threshold joists with drywall screws using your cord-free routine. Make sure you secure the drywall board around the perimeter of the threshold either to the threshold joists or nailers that you installed. It’s my job to install my drywall screws about 6 in . apart on the length of the joist. Continue doing this process unless you have the whole threshold done.

Leave a Reply

Your email address will not be published. Required fields are marked *